BISSELL CrossWave HF3

R8,999.00

Vacuum and wash at the same time with BISSELL CrossWave HF3 Cordless multi-surface wet dry vacuum. Save time by combining two cleaning steps into one across multiple sealed hard floor surfaces, including wood, tile, linoleum, and laminate. CrossWave HF3 Cordless wet dry vac makes cleaning even easier with both high and low modes that automatically dispense the right amount of cleaning solution onto floors. Tackle messes across your home’s floors with up to 25 minutes of quiet, cordless cleaning. Plus, with Self-Propelled Steering, manoeuvrability is easy with minimal effort!

Free Delivery | 7-Day Returns Policy |Warranty: 2 Year limited warranty against manufacturing defects.

1 in stock

Product Notes

  • Quiet & Cordless: Enjoy 25 minutes of quiet, cordless cleaning
  • Smart Touch fingertip controls gives you adaptive and convenient control to best fit your cleaning surface​
  • 22.2V lithium-ion battery
  • Hard Floor Multi-Surface Cleaning: Vacuum & wash hard floors for one-step wet and dry cleaning on wood, tile, linoleum, laminate, & other sealed hard floors.
  • Automatically applies cleaning formula: Includes both high and low modes that automatically dispense cleaning solution onto the floor during use.
  • Self-Cleaning cycle to freshen the brush roll and flush debris into the dirty tank for easy disposal.
  • 3-in-1 Storage tray & Accessory holder
  • Easy to remove brush window and removable brush roll
  • Two tank system: two separate tanks for clean and dirty water.
  • Removable tanks for easy filling and emptying.
  • Always clean with fresh water and formula.
  • Lightweight & Manoeuvrability
  • Effortlessly reach the difficult corners with the swivel foot

Product Care

  • Refer to User Guide & Safety Instructions Included
  • Maintenance: Unplug from electrical socket when not in use and before cleaning, maintaining or servicing the appliance.
  • Empty Dirty Water Tank:
    • 1. To release dirty water tank, press down on recessed button on the top of the dirty tank.
    • 2. Grab the front handle while pressing down on button and pull dirty water tank away from the unit.
    • 3. Grasp top of dirty water tank in recessed areas on each side of the filter and pull upward to remove the top of the tank.
    • 4. To empty, pour dirty water and debris out. Rinse the inside of the dirty water tank.
    • 5. Remove the filter from the dirty water tank top by pulling it up.
    • 6. Hand wash the vacuum filter and screen with warm water and mild detergent.
    • 7. Rinse the float located at the bottom of the dirty water tank’s top.
    • 8. If the inside area where the dirty water tank sits is dirty, wipe it clean with a cloth or towel.
    • 9. Leave parts out to dry.
    • 10. Place vacuum filter back into dirty water tank top.
    • 11. Once parts are dry, reassemble and replace the top of dirty water tank.
    • 12. Angle the dirt tank back into body of machine inserting bottom first. Then tilt the top of the dirt tank toward the machine and push into place until you hear a click.
  • NOTE: Your dirty water tank is full when the dirty water reaches the MAX fill line and/or the float shuts off the suction motor.
  • Maintenance: Cleaning the Brush Roll and Brush Chamber:
    • 1. Turn off and unplug machine from the grounded outlet.
    • 2. Grasp brush roll window at the front and pull upward to remove.
    • 3. Pull brush roll out by grabbing the brush roll tap and pulling upward.
    • 4. With warm water, rinse your brush roll window and brush roll.
    • 5. If your brush roll chamber is dirty clean with a cloth or towel.
    • 6. Let your brush roll and brush roll window chamber dry before reassembling.
    • 7. Replace brush roll by inserting the brush roll end into the right side of the foot. Then lock the pull tab into place by pressing downward.
    • 8. Replace the brush roll window by first lining up the brush window tabs with the edged of the foot. Then press the window back into place until you hear a click.
  • Maintenance: Easy Clean Storage Tray:
    • 1. Place unit on self-cleaning storage tray.
    • 2. Pour water to the max line of the self-cleaning storage tray.
    • 3. Turn the machine on by pressing the Hard Floor Button.
    • 4. Recline the machine while in storage tray. Allow the machine to run for 10-15 seconds until all water is picked up.
    • 5. Unplug the unit.
    • 6. Grasp brush roll window at the front and pull upward to remove.
    • 7. Pull brush roll out by grabbing the brush roll tap and pulling upward.
    • 8. Place brush roll upright in the Brush Roll Drying Tray to dry.
    • 9. Replace brush roll by inserting the brush roll end into the right side of the foot. Then lock the pull tab into place by pressing downward.
    • 10. Replace the brush roll window by first lining up the brush window tabs with the edged of the foot. Then press the window back into place until you hear a click.

Additional Notes

Product Specifications 

  • Power Source: Corded
  • Power (WATT): 340 watts
  • Noise Level: 81.5 db
  • Cleaning Path Width: 15cm
  • Clean Tank: 1.1lt
  • Dirty Tank: 1.4lt
  • Surface Type: Carpet and area rugs, Upholstery, stairs and car
  • Cord Length: 4.6m
  • Hose Length: 1.5m

Product Dimensions

WP Data Tables

Reviews

There are no reviews yet

Only logged in customers who have purchased this product may leave a review.

SKU LO-B3639N Category